Armature-in-a-Can Pro Built - 150mm / 6 Inch Scale
Armature-in-a-Can Pro Built - 150mm / 6 Inch Scale
Armature-in-a-Can Pro Built - 150mm / 6 Inch Scale
Armature-in-a-Can Pro Built - 150mm / 6 Inch Scale
Armature-in-a-Can Pro Built - 150mm / 6 Inch Scale

Armature-in-a-Can Pro Built - 150mm / 6 Inch Scale

£179.99
This Product is In Stock
Armature-in-a-Can Pro Built - 150mm / 6 Inch Scale

The most comprehensive , feature packed stock Animation Armature in the world...........

NEW , UPDATED & IMPROVED!!


"This "canned" professionaly built armature is fully packed with features and ready to go - just open the can, pop the armature out, tension the joints and animate!!
I have always endeavoured to make it possible for everyone, from all levels of expertise and budgets, to be able to produce stop motion animation as close to the professionals as possible. Still hand made in my UK based workshop, using traditional techniques along with the latest laser profiling technology, I am proud to offer this studio quality armature at an affordable price that is worthy of being used by Aardman, one of the greatest stop motion studios in the world." 
(Julian Clark, 2017)


Each Canned Armature is personally designed and built by Julian Clark, armature fabricator for Aardman and supplier of thousands of armatures worldwide to students, enthusiasts and professional studios.


 






Features:
  • 14 Precision Ball & Socket Joints - beautifully smooth with plenty of resistance to material
  • 7 integrated rigging points with M3 threaded 45° & 90° lock-offs - covers front-to-back, side-to-side and vertical axes.
  • Interlocking square brass tube wrist/forearm section
  • Interlocking forearm joints for easy and secure replacement of hands, including 90° M3 threaded lock-offs
  • Natural and anatomically correct shoulder and torso joints - perform "shrug" and front-to-back shoulder movements with precision and control
  • Ball jointed foot set with M3 threaded tie down points in both heel and toe plates
  • Made with over 50 precision steel parts, utilising the latest Laser Cutting technology
  • Powder coated torso and hip section for extra durability

 
 

Ball Stem Technology with traditional silver solder techniques


 

Ball Stems are 6mm balls with an M3 threaded 70mm stem precision made from a single piece of hard wearing stainless steel, completely solving the age old issue of balls being ripped from rod ends during lengthy animation.

These Ball Stems are used throughout the construction of this pre-built armature, with the exception of 3 separate points of articulation - shoulders and lower back section. So, to solve a potential weakness issue, these areas have been professionally silver brazed.







Silver Brazing is a process of joining metal through a heating technique along with the addition of a "filler" metal, this technique is used to permanently secure a stainless steel ball to a stainless steel rod, joining lock-off points to brass tubing (lock-off's are used to secure rigging points or interlocking tubing) and to join steel components.

This armature has silver brazed brass interlocking rigging points, interlocking wrist sections, interlocking neck section, shoulder ball joints, lower back section and foot components (one of the most important areas for strength on an armature).



 

 

New smaller Foot Component with Toe Pivot Joint & 2 integrated tie down points





A strong, stable foot set with two M3 threaded tie down points positioned in the toe and heel section, plus restricted lateral movement on toe pivot point to ensure natural foot movement.







 







Integrated Interlocking Rigging points covering all three axes
 
Stability of you puppet will always be paramount, therefore successfully rigging your armature will not only make animating a whole lot easier, but will enable you to execute technical moves such as jumping, falling or even flying.

So, this armature comes equipped with SEVEN integrated, interlocking rigging points to cover all possible points of connection, all positioned in the torso and hip, along with 45 and 90 degree lock-off's to secure the corresponding "rig arm".

You simply insert the rig arm (normally square metal bar with a steel ball attached) into the rigging point and tighten the M3 grub screw down onto the arm.

There are many rigging solutions available in the "Rigging" section of this site.









 


Technical Information

Technical Drawing and actual size print sheet are available to download below



















 



Type: Ball & Socket
Material: Mild steel construction with stainless steel Balls & Ball Stems
Weight: 155 Grams
Joint Size: Length 16mm/0.63" x width 7mm/0.27" x depth 8mm/0.31"
Ball size: 6mm diameter stainless steel 
Rod size: M3/3mm stainless steel 
No. Joints: 18
Tie Down: M3 tie down in toe and heel plate, magnetic as standard
Rigging: K&S type square brass tubing in Torso & Hip Joint, will accept 3.18mm (1/8") square tubing. All with 45° and 90°, M3 threaded lock-off points
Contents:
1 x Pre-Built Armature
1 x 30mm Rig Arm
1 x 100cm Spool of 1mm Aluminium Armature Wire
1 x 100cm Spool of 0.75mm Copper wire (for reinforcing wire fingers)
1 x Allen Key Set (1.5mm, 2mm & 2.5mm Allen Keys)
1 x Spares Bag (Bolts, Nuts etc)



 
Specification
Brand JulianClarkStudios
Weight 0.25kg
This product has received no reviews, be the first to write a review!
Delivery & Returns
Delivery & Returns Information